Application Description :
- Tape Cutter Device.
- Tape Cutter Device
TC
| Description | Application | Parts List | |
|---|---|---|---|
|
TC021H, TC021K, TC022H, TC022K, TC022S |
・[Description]The knife is installed behind the needle plate. At the end of sewing, TC device cuts the tape or thread chain. Many product packages are available with sensors, manual switch, knee switch, pneumatic and solenoid type actuator..., etc. | ・[Application]UH9000F, UHD9000F, UHF9000, UHU9000 | ・[Parts List] |
|
TC023H, TC023K, TC023S, TC024H, TC024K, TC024S |
・[Description]The knife is installed behind the needle plate. At the end of sewing, TC device cuts the tape or thread chain. Many product packages are available with sensors, manual switch, knee switch, pneumatic and solenoid type actuator..., etc. | ・[Application]UH9000F, UHD9000F, UHF9000, UHU9000 | ・[Parts List] |
- Tape Cutter Device
TC
| TC TCS |
Picture | Cutting Width | Blade to Presser foot | Actuation | Needle Plate | Application | Parts List |
|---|---|---|---|---|---|---|---|
|
TC001, TC004, TCS01, TCS04, |
・[Picture] |
・[Cutting Width]32mm | ・[Blade to Presser foot]31.9mm | ・[Actuation ]Pneumatic | ・[Needle Plate]Standard needle plate | ・[Application] TC001/ TCS01 : FT7003, FTD7003, FTU7003 TC004/ TCS04 : FT7069, FTD7069 | ・[Parts List]
|
|
TC002, TC005, TCS02, TCS05, |
・[Picture] |
・[Cutting Width]32mm | ・[Blade to Presser foot]31.9mm | ・[Actuation ]Electric | ・[Needle Plate]Standard needle plate | ・[Application] TC002/ TCS02 : FT7003, FTD7003, FTU7003 TC005/ TCS05 : FT7069, FTD7069 | ・[Parts List]
|
|
TC003, TCS03, |
・[Picture] |
・[Cutting Width]28mm | ・[Blade to Presser foot]5.3mm | ・[Actuation ]Pneumatic | ・[Needle Plate] |
・[Application] (356,364): FT7003, FTD7003, FTU7003 | ・[Parts List]
|
|
TC008, TCS08, |
・[Picture] |
・[Cutting Width]28mm | ・[Blade to Presser foot]11mm | ・[Actuation ]Pneumatic | ・[Needle Plate] |
・[Application] FT7002, FTD7002 | ・[Parts List]
|
|
TC009, TC019, TCS09, TCS19 |
・[Picture] |
・[Cutting Width]28mm | ・[Blade to Presser foot]12.3mm | ・[Actuation ]Pneumatic | ・[Needle Plate]  |
・[Application] TC009/TCS09 : FT□7003, FT□7069-0, FT□7069-2 FT□7069-4, FTD7069-6 TC019/TCS19 : FT□7069-3, FT□7069-5 FTD7069-7 | ・[Parts List]
|
| TCS33 | ・[Picture] |
・[Cutting Width]28mm | ・[Blade to Presser foot]25mm | ・[Actuation ]Pneumatic | ・[Needle Plate]Standard needle plate | ・[Application]
FT7000, FTD7000 Top mounted type moving knife makes sewing area free without obstacal. |
・[Parts List]
|
Pneumatic : Compressed air is required(5kg/ cm2 或 70 PSI)
TCS series is controlled by servo motor controller
TC series is equipped with the independent controller
TCS series is controlled by servo motor controller
TC series is equipped with the independent controller
- NTD67 Tape (Thread) Cutter
TC
| TC | Cutter Type | Air Cylinder | Waste Suction | CV Set | Cutter Switch | Sensor | Servo Motor | Parts List |
|---|---|---|---|---|---|---|---|---|
| TC012E | ・[ Cutter Type]Punch type(with Blade) | ・[Air Cylinder]Round type | ・[Waste Suction] - | ・[CV Set] CV015, CV016 | ・[Cutter Switch] Hand touch | ・[Sensor] - | ・[Servo Motor] TD715 | ・[Parts List]
|
| TC012K | ・[ Cutter Type]Punch type(with Blade) | ・[Air Cylinder]Round type | ・[Waste Suction] - | ・[CV Set] CV015, CV016 | ・[Cutter Switch] Knee touch | ・[Sensor] - | ・[Servo Motor] TD715 | ・[Parts List]
|
| TC012S | ・[ Cutter Type]Punch type(with Blade) | ・[Air Cylinder]Round type | ・[Waste Suction]Rear type | ・[CV Set] CV022 | ・[Cutter Switch] Hand/ Knee touch | ・[Sensor] ● | ・[Servo Motor] i-70 | ・[Parts List]
|
| TC112E | ・[ Cutter Type]Punch type | ・[Air Cylinder]Round type | ・[Waste Suction] - | ・[CV Set] CV015, CV016 | ・[Cutter Switch] Hand touch | ・[Sensor] - | ・[Servo Motor] TD715 | ・[Parts List]
|
| TC112K | ・[ Cutter Type]Punch type | ・[Air Cylinder]Round type | ・[Waste Suction] - | ・[CV Set] CV015, CV016 | ・[Cutter Switch] Knee touch | ・[Sensor] - | ・[Servo Motor] TD715 | ・[Parts List]
|
 TC112S
|
・[ Cutter Type]Punch type | ・[Air Cylinder]Round type | ・[Waste Suction]Bottom type | ・[CV Set] CV022 | ・[Cutter Switch] Hand/ Knee touch | ・[Sensor] ● | ・[Servo Motor] i-70 | ・[Parts List]
|
• As Punchtype cutter, the presser foot can be removed directly without removing the cutter in advance,
which is suitable for the garment factories that frequently adjust machines for style changing.
• The bottom suction tube can free up the rear space to avoid jamming behind the cutter. It is suitable for NTD 6703 (tape attaching), but it will increase the circumference of the arm-bed.
• CV015 has a standard pipe diameter of Ø19 and is suitable for general fabrics. CV016 has an enlarged pipe diameter of Ø25 and is suitable for thick fabrics.
• The bottom suction tube can free up the rear space to avoid jamming behind the cutter. It is suitable for NTD 6703 (tape attaching), but it will increase the circumference of the arm-bed.
• CV015 has a standard pipe diameter of Ø19 and is suitable for general fabrics. CV016 has an enlarged pipe diameter of Ø25 and is suitable for thick fabrics.
斬刀/ 下吸
斬刀/ 後吸
| TC | Cutter Type | Air Cylinder | Waste Suction | CV Set | Cutter Switch | Sensor | Servo Motor | Parts List |
|---|---|---|---|---|---|---|---|---|
| TC013E | ・[ Cutter Type]Chop type | ・[Air Cylinder]Square type | ・[Waste Suction] - | ・[CV Set] CV015, CV016 | ・[Cutter Switch] Hand touch | ・[Sensor] - | ・[Servo Motor] TD715 | ・[Parts List]
|
| TC013K | ・[ Cutter Type]Chop type | ・[Air Cylinder] Square type | ・[Waste Suction] - | ・[CV Set] CV015, CV016 | ・[Cutter Switch] Knee touch | ・[Sensor] - | ・[Servo Motor] TD715 | ・[Parts List]
|
| TC013S | ・[ Cutter Type]Chop type | ・[Air Cylinder] Square type | ・[Waste Suction]Rear type | ・[CV Set] CV022 | ・[Cutter Switch] Hand/ Knee touch | ・[Sensor] ● | ・[Servo Motor] i-70 | ・[Parts List]
|
| TC113S | ・[ Cutter Type]Chop type | ・[Air Cylinder] Square type | ・[Waste Suction] Bottom type | ・[CV Set] CV022 | ・[Cutter Switch] Hand/ Knee touch | ・[Sensor] ● | ・[Servo Motor] i-70 | ・[Parts List]
|
| TC014S | ・[ Cutter Type]Chop type Moving knife with spring-pressed | ・[Air Cylinder] Square type | ・[Waste Suction] Rear type | ・[CV Set] CV022 | ・[Cutter Switch] Hand/ Knee touch | ・[Sensor]● | ・[Servo Motor] i-70 | ・[Parts List]
|
| TC024S | ・[ Cutter Type]Chop type Moving knife with spring-pressed | ・[Air Cylinder]Square type | ・[Waste Suction] Rear type | ・[CV Set] CV022 | ・[Cutter Switch] Hand/ Knee touch | ・[Sensor]● | ・[Servo Motor] i-70 | ・[Parts List]
|
• The bottom suction tube can free up the rear space to avoid jamming behind the cutter. It is suitable for NTD 6703 (tape attaching), but it will increase the circumference of the arm-bed.
• CV015 has a standard pipe diameter of Ø19 and is suitable for general fabrics. CV016 has an enlarged pipe diameter of Ø25 and is suitable for thick fabrics.
• TC 024S is the same as TC 014S, only the side cover fixing plate is different.
• CV015 has a standard pipe diameter of Ø19 and is suitable for general fabrics. CV016 has an enlarged pipe diameter of Ø25 and is suitable for thick fabrics.
• TC 024S is the same as TC 014S, only the side cover fixing plate is different.
- NTD77 Tape (Thread) Cutter
TC
| TC | Cutter Type | Actuator | Waste Suction | CV Set | Cutter Switch | Sensor | Press Foot Lifter | Parts List |
|---|---|---|---|---|---|---|---|---|
| TC026A | ・[ Cutter Type]Punch type | ・[Actuator]Air Cylinder (Round) | ・[Waste Suction] Rear type | ・[CV Set] CV023 | ・[Cutter Switch] Hand Touch, Optional: Knee control kit | ・[Sensor] - | ・[Press Foot Lifter] Pneumatic | ・[Parts List]
|
| TC026AS | ・[ Cutter Type]Punch type | ・[Actuator] Air Cylinder (Round) | ・[Waste Suction] Rear type | ・[CV Set] CV023 | ・[Cutter Switch] Hand Touch, Optional: Knee control kit | ・[Sensor] ● | ・[Press Foot Lifter] Pneumatic | ・[Parts List]
|
| TC026B | ・[ Cutter Type]Punch type | ・[Actuator] Air Cylinder (Round) | ・[Waste Suction] Rear type | ・[CV Set] CV023 | ・[Cutter Switch] Hand Touch, Optional: Knee control kit | ・[Sensor] - | ・[Press Foot Lifter] Solenoid | ・[Parts List]
|
| TC026BS | ・[ Cutter Type]Punch type | ・[Actuator] Air Cylinder (Round) | ・[Waste Suction] Rear type | ・[CV Set] CV023 | ・[Cutter Switch] Hand Touch, Optional: Knee control kit | ・[Sensor] ● | ・[Press Foot Lifter] Solenoid | ・[Parts List]
|
| TC027A | ・[ Cutter Type]Punch type (with Blade) | ・[Actuator] Air Cylinder (Round) | ・[Waste Suction] Rear type | ・[CV Set] CV023 | ・[Cutter Switch] Hand Touch, Optional: Knee control kit | ・[Sensor] - | ・[Press Foot Lifter] Pneumatic | ・[Parts List]
|
| TC027AS | ・[ Cutter Type]Punch type (with Blade) | ・[Actuator] Air Cylinder (Round) | ・[Waste Suction] Rear type | ・[CV Set] CV023 | ・[Cutter Switch] Hand Touch, Optional: Knee control kit | ・[Sensor] ● | ・[Press Foot Lifter] Pneumatic | ・[Parts List]
|
| TC027B | ・[ Cutter Type]Punch type (with Blade) | ・[Actuator] Air Cylinder (Round) | ・[Waste Suction] Rear type | ・[CV Set] CV023 | ・[Cutter Switch] Hand Touch, Optional: Knee control kit | ・[Sensor] - | ・[Press Foot Lifter] Solenoid | ・[Parts List]
|
| TC027BS | ・[ Cutter Type]Punch type (with Blade) | ・[Actuator] Air Cylinder (Round) | ・[Waste Suction] Rear type | ・[CV Set] CV023 | ・[Cutter Switch] Hand Touch, Optional: Knee control kit | ・[Sensor] ● | ・[Press Foot Lifter] Solenoid | ・[Parts List]
|
Remark：
• As Punchtype cutter, the presser foot can be removed directly without removing the cutter in advance, which is suitable for the garment factories that frequently adjust machines for style changing.
• Tape Cutting isrecommended to use TC027 punch type with blade, or TC028A pneumatic type chopping cutter, for better efficiency.
• As Punchtype cutter, the presser foot can be removed directly without removing the cutter in advance, which is suitable for the garment factories that frequently adjust machines for style changing.
• Tape Cutting isrecommended to use TC027 punch type with blade, or TC028A pneumatic type chopping cutter, for better efficiency.
氣動式/ 斬刀
| TC | Cutter Type | Actuator | Waste Suction | CV Set | Cutter Switch | Sensor | Press Foot Lifter | Parts List |
|---|---|---|---|---|---|---|---|---|
| TC028A | ・[ Cutter Type]Chop type | ・[Actuator] Air Cylinder (Square) | ・[Waste Suction] Rear type | ・[CV Set] CV023 | ・[Cutter Switch] Hand Touch, Optional: Knee control kit | ・[Sensor] - | ・[Press Foot Lifter] Pneumatic | ・[Parts List]
|
|
TC028AS
|
・[ Cutter Type]Chop type | ・[Actuator] Air Cylinder (Square) | ・[Waste Suction] Rear type | ・[CV Set] CV023 | ・[Cutter Switch] Hand Touch, Optional: Knee control kit | ・[Sensor] ● | ・[Press Foot Lifter] Pneumatic | ・[Parts List]
|
| TC028B | ・[ Cutter Type]Chop type | ・[Actuator] Air Cylinder (Square) | ・[Waste Suction] Rear type | ・[CV Set] CV023 | ・[Cutter Switch] Hand Touch, Optional: Knee control kit | ・[Sensor] - | ・[Press Foot Lifter] Solenoid | ・[Parts List]
|
| TC028BS | ・[ Cutter Type]Chop type | ・[Actuator] Air Cylinder (Square) | ・[Waste Suction] Rear type | ・[CV Set] CV023 | ・[Cutter Switch] Hand Touch, Optional: Knee control kit | ・[Sensor] ● | ・[Press Foot Lifter] Solenoid | ・[Parts List]
|
| TC028C | ・[ Cutter Type]Chop type | ・[Actuator] Solenoid | ・[Waste Suction] Rear type | ・[CV Set] CV023 | ・[Cutter Switch] Hand Touch, Optional: Knee control kit | ・[Sensor] - | ・[Press Foot Lifter] Solenoid | ・[Parts List]
|
|
TC028CS
|
・[ Cutter Type]Chop type | ・[Actuator] Solenoid | ・[Waste Suction] Rear type | ・[CV Set] CV023 | ・[Cutter Switch] Hand Touch, Optional: Knee control kit | ・[Sensor] ● | ・[Press Foot Lifter] Solenoid | ・[Parts List]
|
Remark：
• As Punchtype cutter, the presser foot can be removed directly without removing the cutter in advance, which is suitable for the garment factories that frequently adjust machines for style changing.
• Tape Cutting isrecommended to use TC027 punch type with blade, or TC028A pneumatic type chopping cutter, for better efficiency.
• As Punchtype cutter, the presser foot can be removed directly without removing the cutter in advance, which is suitable for the garment factories that frequently adjust machines for style changing.
• Tape Cutting isrecommended to use TC027 punch type with blade, or TC028A pneumatic type chopping cutter, for better efficiency.
- General Type Rear Cutter
TCA
| TC | Picture | Cutter Type | Air Cylinder | Waste Suction | CV Set | Cutter Switch | Sensor | Servo Motor | Application |
|---|---|---|---|---|---|---|---|---|---|
|
TCA67 TCA77 TCA80 |
・[ Picture]  |
・[ Cutter Type]Chop type Moving knife with spring-pressed | ・[Air Cylinder] Square type | ・[Waste Suction] Rear type | ・[CV Set] Standard | ・[Cutter Switch] Pedal: Heeling backward | ・[Sensor]● | ・[Servo Motor] TD415 | ・[Application]TCA67:NTD67 TCA77:NTD77 TCA80:NTD80 |
Remark：
TCA cutter set features a modular design and is compatible with the full range of NTD 67/77/80 series.
In manual mode, the cutter is controlled by pressing the rear of the foot pedal.
Supports automatic mode, with fabric edge detection sensor as standard equipment.
TCA cutter set features a modular design and is compatible with the full range of NTD 67/77/80 series.
In manual mode, the cutter is controlled by pressing the rear of the foot pedal.
Supports automatic mode, with fabric edge detection sensor as standard equipment.
- Pneumatic Tape Cutter
TCS34
| TCS | Picture | Directions | Parts List |
|---|---|---|---|
| TCS34 | ・[Picture]  |
・[Directions]Max. cutting width 18 mm. The gap between knife and presser foot is 28 mm. | ・[Parts List]
|