Application Description :
- Tape Cutter Device
TC021H, TC021K, TC022H, TC022K, TC022S, TC023H, TC023K, TC023S, TC024H TC024K TC024S
Tape Cutter Device
| TC | picturew | picturew | Application | Directions | Parts List |
|---|---|---|---|---|---|
| TC021H, TC021K, TC022H, TC022K, TC022S |
|
|
UH9000F, UHD9000F, UHF9000, UHU9000 |
The knife is installed behind the needle plate. At the end of sewing, TC device cuts the tape or thread chain. Many product packages are available with sensors, manual switch, knee switch, pneumatic and solenoid type actuator..., etc. |  |
| TC023H, TC023K, TC023S, TC024H, TC024K, TC024S |
|
TCS31,TCS32
Tape Cutter Device
| TC | picturew | picturew | Application | Directions | Parts List |
|---|---|---|---|---|---|
| TCS31 | 
|
|
CTD9700 | Max. cutting width 18 mm. The gap between knife and presser foot is 28 mm. |
|
| TCS32 | CXM2000 |
|
TC001,TC004, TCS01, TCS04, TC002, TC005, TCS02, TCS05, TC003, TCS03, TC008, TCS08, TC009, TC019, TCS09, TCS19, TCS33
Tape Cutter Device
| TC | picturew | picturew | Cutting Width | Blade to Presser foot | Actuation | Needle Plate | Directions | Parts List |
|---|---|---|---|---|---|---|---|---|
| TC001, TC004, TCS01, TCS04, |
|
|
32mm | 31.9mm | Pneumatic | Standard needle plate | TC001/ TCS01 : FT7003, FTD7003 FTU7003 TC004/ TCS04 : FT7069, FTD7069 |
|
| TC002, TC005, TCS02, TCS05, |
|
|
32mm | 31.9mm | Electric | Standard needle plate | TC002/ TCS02 : FT7003, FTD7003 FTU7003 TC005/ TCS05 : FT7069, FTD7069 |
|
| TC003, TCS03 |
|
|
28mm | 5.3mm | Pneumatic |  |
FT7003(356, 364) FTD7003(356, 364) |
|
| TC008, TCS08 |
|
|
28mm | 11mm | Pneumatic |  |
FT7002 FTD7002 |
|
| TC009, TC019, TCS09, TCS19 |
28mm | 12.3mm | Pneumatic |
|
TC009/TCS09 : FT7003, FTD7003 FTU7003 FT7069-0, FT7069-2 FT7069-4, FT7069-6 FTD7069-0 FTD7069-2 FTD7069-4 FTD7069-6 TC019/TCS19 : FT7069-3, FT7069-5 FT7069-7 FTD7069-3 FTD7069-5 FTD7069-7 |
|
||
| TCS33 | 
|
28mm | 25mm | Pneumatic | Standard needle plate | FT7000, FTD7000 Top mounted type moving knife makes sewing area free without obstacal. |
|
TC012E, TC012K, TC012S, TC112E, TC112K, TC112S, TC013E, TC013K, TC013S, TC113S, TC014S
Tape (Thread) Cutter
| TC | picturew | Cutter Type | Air Cylinder | Waste Suction | CV Set | Cutter Switch | Sensor | Servo Motor | Application | Directions | video | Parts List |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| TC012E | - | Punch type(with Blade) | Round type | - | CV015, CV016 | Hand touch | - | TD715 | NTD67 | As Punch type cutter, the presser foot can be removed directly without removing the cutter in advance, which is suitable for the garment factories that frequently adjust machines for style changing. CV015 has a standard pipe diameter of Ø19 and is suitable for general fabrics. CV016 has an enlarged pipe diameter of Ø25 and is suitable for thick fabrics. |
- | |
| TC012K | - | Punch type(with Blade) | Round type | - | Knee touch | - | TD715 | NTD67 | - | |
||
| TC012S | - | Punch type(with Blade) | Round type | Rear type | CV022 | Hand/ Knee touch | ● | i-70 | NTD67 | - | |
|
| TC112E | - | Punch type | Round type | - | CV015, CV016 | Hand touch | - | TD715 | NTD67 | As Punch type cutter, the presser foot can be removed directly without removing the cutter in advance, which is suitable for the garment factories that frequently adjust machines for style changing. CV015 has a standard pipe diameter of Ø19 and is suitable for general fabrics. CV016 has an enlarged pipe diameter of Ø25 and is suitable for thick fabrics. |
- | |
| TC112K | - | Punch type | Round type | - | Knee touch | - | TD715 | NTD67 | - | |
||
| TC112S |  |
Punch type | Round type | Bottom type | CV022 | Hand/ Knee touch | ● | i-70 | NTD67 | 
|
|
|
| TC013E | - | Chop type | Square type | - | CV015, CV016 | Hand touch | - | TD715 | NTD67 | CV015 has a standard pipe diameter of Ø19 and is suitable for general fabrics. CV016 has an enlarged pipe diameter of Ø25 and is suitable for thick fabrics. | - | |
| TC013K | - | Chop type | Square type | - | Knee touch | - | TD715 | NTD67 | - | |
||
| TC013S |  |
Chop type | Square type | Rear type | CV022 | Hand/ Knee touch | ● | i-70 | NTD67 | - | - | |
| TC113S |  |
Chop type | Square type | Bottom type | CV022 | Hand/ Knee touch | ● | i-70 | NTD67 | The bottom suction tube can free up the rear space to avoid jamming behind the cutter. It is suitable for NTD 6703 (tape attaching), but it will increase the circumference of the arm-bed. | - |
|
| TC014S | - | Chop type Moving knife with spring-pressed | Square type | Rear type | CV022 | Hand/ Knee touch | ● | i-70 | NTD67 | TC 024S is the same as TC 014S, only the side cover fixing plate is different. | - |
|
TC026A, TC026AS, TC026B, TC026BS, TC027A, TC027AS, TC027B, TC027BS, TC028A, TC028AS, TC028B, TC028BS, TC028C, TC028CS
Tape (Thread) Cutter
| TC | picturew | Cutter Type | Actuator | Waste Suction | CV Set | picturew | Cutter Switch | Sensor | Press Foot Lifter | Application | Directions | video | Parts List |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| TC026A | - | Punch type | Air Cylinder (Round) | Rear type | CV023 | 
|
Hand touch Optional: Knee control kit 4TC001A0310 |
- | Pneumatic | NTD77 | As Punch type cutter, the presser foot can be removed directly without removing the cutter in advance, which is suitable for the garment factories that frequently adjust machines for style changing. | - | |
| TC026AS |  |
Punch type | Air Cylinder (Round) | Rear type | ● | Pneumatic | NTD77 | - | |||||
| TC026B | - | Punch type | Air Cylinder (Round) | Rear type | Hand touch Optional: Knee control kit 4TC001A0310 |
- | Electric | NTD77 | - | ||||
| TC026BS | - | Punch type | Air Cylinder (Round) | Rear type | ● | Electric | NTD77 | - | |||||
| TC027A | - | Punch type(with Blade) | Air Cylinder (Round) | Rear type | CV023 |
|
Hand touch Optional: Knee control kit 4TC001A0310 |
- | Pneumatic | NTD77 |
As Punch type cutter, the presser foot can be removed directly without removing the cutter in advance, which is suitable for the garment factories that frequently adjust machines for style changing.
Tape Cutting is recommended to use TC027 punch type with blade, or TC028A pneumatic type chopping. |
- |
|
| TC027AS |  |
Punch type(with Blade) | Air Cylinder (Round) | Rear type | ● | Pneumatic | NTD77 | - | |||||
| TC027B | - | Punch type(with Blade) | Air Cylinder (Round) | Rear type | Hand touch Optional: Knee control kit 4TC001A0310 |
- | Solenoid | NTD77 | - | ||||
| TC027BS | - | Punch type(with Blade) | Air Cylinder (Round) | Rear type | ● | Solenoid | NTD77 | - | |||||
| TC028A | - | Chop type | Air Cylinder (Square) | Rear type | CV023 |
|
Hand touch Optional: Knee control kit 4TC001A0310 |
- | Pneumatic | NTD77 | Tape Cutting is recommended to use TC027 punch type with blade, or TC028A pneumatic type chopping. | - | |
| TC028AS |  |
Chop type | Air Cylinder (Square) | Rear type | CV023 | ● | Pneumatic | NTD77 | |||||
| TC028B | - | Chop type | Air Cylinder (Square) | Rear type | CV023 | Hand touch Optional: Knee control kit 4TC001A0310 |
- | Solenoid | NTD77 | - | - | ||
| TC028BS |  |
Chop type | Air Cylinder (Square) | Rear type | CV023 | ● | Solenoid | NTD77 | - | - | |||
| TC028C | - | Chop type | Solenoid | Rear type | CV023 | Hand touch Optional: Knee control kit 4TC001A0310 |
- | Solenoid | NTD77 | - | - | |
|
| TC028CS |  |
Chop type | Solenoid | Rear type | CV023 | ● | Solenoid | NTD77 | - |
|
TCS34
Pneumatic Tape Cutter
| TCS34 | picturew | picturew | Application | Directions | Parts List |
|---|---|---|---|---|---|
|
|
FTK2500 | Max. cutting width 18 mm. The gap between knife and presser foot is 28 mm. | |